Masaba 48″ Low Profile Truck Unloader (model LPTU48) available!

Located in the Houston area.  Priced at $310K

Contact Pete Cook at [email protected] or text 540-222-2742 for additional information or an introduction to the seller.

GENERAL SPECIFICATIONS
• Hydraulic Unit – 20hp electric pumping unit to electrically control ramps and conveyor discharge
raise and lower, including continuous cycling and hot climate protection, 24V Solenoids
• 13hp Electric start Gas Powered Unit – to manually operate hydraulic landing legs, conveyor
raise/lower, and hinged ramp raise/lower, independently, to remove from truck and setup.

• Electrical – 480V/3ph/60Hz enclosed panel. Includes main disconnect, circuit breaker and push
button on/off switches with soft start. Mounted to chassis. With 100’ lead cord
• Guarding – Appropriate guarding supplied. We do not warrant that our guards will meet all local
codes. It is the responsibility of the end user to have them checked by a local inspector
• Steel Shot Blasted Page 2 of 2
• Primer – (1) coat of 2 part urethane primer
• Paint – (1) coat of 2 part urethane paint
• Owner’s Manual – (1) copy in English included for operation, maintenance, and parts

CHASSIS
• Frame – Constructed of Heavy Duty steel tubing
• Tandem Axle – Tandem walking beam with (8) 11×22.5R tires
• Landing Jacks – hydraulic landing legs
• Road Portable Package – Including 5th wheel hitch, brakes, lights and mud flaps
48” DISCHARGE CONVEYOR (approx. 48” x 46’)
• Undercarriage – Hydraulic raise and lower, 11’ maximum discharge height
• Frame – Channel frame
• Drive – Dual Class II head drive with V-Belts and Guard
• Gear Reducers – (2) Dodge shaft mount reducers with sheaves, bushings, and backstops
• Motors – (2) WEG 25hp 1800rpm
• Capacity – 1,000 STPH of 100 PCF material, 1.5” minus spherical lumps
• Belt Speed – 225 FPM
• Flow Control – manual adjustable slide gate
• Steel Hold Down Wheels
• Loading Area Idlers – PPI, CEMA C, 5” diameter flat carrier idlers
• Transition Idlers – PPI, CEMA C, 20 degree, sealed, 5” diameter trough idlers
• Troughing Idlers – PPI, CEMA C, 35 degree, sealed, 5” diameter trough idlers
• Return Idlers – PPI, CEMA C, sealed, 5” diameter rubber disc return idlers
• Drive Pulley – PPI Heavy Duty, 20” diameter, drum pulley with 1/2″ herringbone lagging
• Tail Pulley – PPI Heavy Duty, 14” diameter, self-cleaning wing pulley
• Snub Pulley – PPI Heavy Duty, 14” diameter, drum pulley with 3/8” smooth rubber lagging
• Shafts – C1045 turned and polished
• Bearings – Dodge Pillow block bearings
• Take Ups – Screw type
• Belting – 3-ply 3/16 x 1/16 330 PIW
• Belt Splice – Mechanical – option taken for vulcanized
• Belt Scraper – Flexco EZP1
• Discharge Hood – with 5/16” AR countersunk bolt in liners, to feed 36” belt width or greater

LOAD AREA
• Self-Relieving Load Area Page 1 of 2
• Grate – Constructed of Heavy Duty flat bar, 10’ x 5’ outside dimension
• Two Ramp System – Located on each side of the Loading area.
o Includes (2) Self-Cleaning Ramps – Hinged on each side of grate, hydraulically folding
for cleaning after each loading and travel
o Includes (2) Outer ramps – 10’ wide by 9’ long, put in place manually with loader, stored
inside folding ramp for travel

Vulcanized Belt Splice
Wireless Remote Control System
Additional Remote
Intraflo Central Lube System